1. General Description
The specification is a transmissive type color active matrix liquid crystal display (LCD) which uses amorphous thin film transistor (TFT) as switching devices. This product is composed of a TFT-LCD panel, driver Icsand a backlight unit.
2. Module Parameter
Features | Details | Unit |
Display Size(Diagonal) | 8.0” | |
LCD type | IPS TFT | |
Display Mode | Transmissive/normally black | |
Resolution | 1024*(RGB)x768 | Pixels |
View Direction | FULL VIEW | Best Image |
Module Outline | 175.26(H) x142(V) x 2.95(T) (Note1 ) | mm |
Active Area | 162.05(H) x121.54(V) | mm |
Pixel Size | 158(H)x158(V) | um |
Pixel Arrangement | R.G.B. Vertical Stripe | |
Surface treatment | Hard coating | |
Display Colors | 16.7M | |
Interface | 6 bit/8 bit -LVDS interface | |
With or Without Touch Panel | Without | |
Operating Temperature | -20～70 | ºC |
Storage Temperature | -30～70 | ºC |
Weight | 142 | g |
Note 1: Exclusive hooks, posts , FFC/FPC tail etc.
3.Absolute Maximum Ratings
VSS=0V, Ta=25ºC
Item | Symbol | Min. | Max. | Unit |
Supply Voltage | VDD | (-0.3) | (5.0) | V |
AVDD | (6.5) | (13.5) | V | |
VGH | (-0.3) | (VGL+40.0) | V | |
VGL | (-20.0) | (0.3) | V | |
Storage temperature | Tstg | -30 | +70 | ºC |
Operating temperature | Top | -20 | +70 | ºC |
Note 1: If Ta below 50ºC, the maximal humidity is 90%RH, if Ta over 50ºC, absolute humidity should be less than 60%RH.
Note 2: The response time will be extremely slow when the operating temperature is around -10℃, and the back ground will become darker at high temperature operating.
4. DC Characteristics
Item | Symbol | Min. | Typ. | Max. | Unit |
Supply Voltage | VDD | (3.0) | (3.3) | (3.6) | V |
AVDD | (9.8) | (10) | (10.2) | V | |
VGH | (18.6) | (18.9) | (19.2) | V | |
VGL | (-8.1) | (-7.8) | (-7.5) | V | |
Input signal voltage | VCOM | (2.6) | (3.6) | (4.6) | V |
Input logic high voltage | VIH | (0.7*VDD) | - | (VDD) | V |
Input logic low voltage | VIL | 0 | - | (0.3*VDD) | V |
Current Consumption | ICC+IIN | - | TBD | - | mA |
Note 1:Be sure to apply VCC and VGL to the LCD first,and then apply VGH
Note 2:VCC setting should match the signal output voltage (refer to Note 3)of customer’s system board
Note 3:Typical Vcom is only a reference value ,it must be optimized according to each LCM
Note 4:DCLK,HS,VS,RSTB,UPDN,STLR,MODE,DITHB
5. Backlight Characteristic
5.1. Backlight Characteristic
Item | Symbol | Condition | Min | Typ | Max | Unit |
Forward Voltage | VF | Ta=25ºC,IF=20mA | - | 9.8 | - | V |
Forward Current | IF | Ta=25ºC, VF=9.8V | - | 240*2 | - | mA |
Power dissipation | Pd | - | 4704 | - | W | |
Uniformity | Avg | 65 | - | - | % | |
Drive method | Constant current | |||||
LEDConfiguration | 72 White LEDs (3 LEDs in one string and 12 groups in parallel)*2 | |||||